板式雙管板換熱器在使用的過程中會遇到一些故障情況，比如遇到了外漏情況，這時候我們要先分析為何會產生這樣的情況，然后在進一步分析如何處理以及下次如何避免再次發生。
1、雙管板換熱器外漏產生原因：①夾緊尺寸不到位、各處尺寸不均勻(各處尺寸偏差不應大于3 mm)或夾緊螺栓松動。② 部分密封墊脫離密封槽，密封墊主密封面有臟物，密封墊損壞或板式換熱器密封墊片老化。③ 板片發生變形，組裝錯位引起跑墊。④在板片密封槽部位或二道密封區域有裂紋。實例：北京、青海和新疆等地的多個熱力站均采用飽和蒸汽作為一次側熱源供暖，由于蒸汽溫度較高，在設備運行初期系統不穩定的情況下，橡膠密封墊在高溫下失效，引起蒸汽外漏。
2、雙管板換熱器外漏處理方法：① 在無壓狀態，按制造廠提供的夾緊尺寸重新夾緊設備，尺寸應均勻一致，壓緊尺寸的偏差應不大于±0.2N (mm)(N。為板片總數)，兩壓緊板間的平行度應保持在2 mm 以內。② 在外漏部位上做好標記，然后換熱器解體逐一排查解決，重新裝配或更換墊片和板片。③ 將開換熱器解體，對板片變形部位進行修理或者更換板片。在沒有板片備件時可將變形部位板片暫時拆除后重新組裝使用。④ 重新組裝拆開的板片時，應清潔板面，防止污物粘附著于墊片密封面。
相信如果遇到了一次故障問題之后，在之后使用雙管板換熱器會更加的小心謹慎，避免在發生同樣的情況啦。
上一篇：不銹鋼潔凈管道安裝需知
下一篇：如何設計潔凈管道系統
